TD1410 PDF

Techcode TD datasheet, 2A KHZ 20V PWM Buck DC/DC Converter (1- page), TD datasheet, TD pdf, TD datasheet pdf, TD pinouts. Find great deals for 5pcs Power PWM Controller TD Sop8. Shop with confidence on eBay!. Altech TD Terminals are available at Mouser Electronics. Mouser offers inventory, pricing, & datasheets for Altech TD Terminals.

Author: Kigor Mumuro
Country: Paraguay
Language: English (Spanish)
Genre: Health and Food
Published (Last): 5 November 2007
Pages: 48
PDF File Size: 20.99 Mb
ePub File Size: 19.56 Mb
ISBN: 130-7-98594-956-4
Downloads: 34800
Price: Free* [*Free Regsitration Required]
Uploader: Yozshukus

Some of these factors include board size, tx1410, thickness, position, location, and even board temperature. Once exception to this is the output switch pin, which should not have large areas of copper. Through an external resistor divider network, FB senses the output voltage and regulates it.

Higher ambient temperatures require more heat sinking. An additional small LC filter can be added to the output as shown in Figure 14 to further reduce the amount of output ripple and transients. FB Senses the regulated output voltage to complete the feedback loop. The output ripple voltage is due mainly to the inductor sawtooth ripple current multiplied by the ESR of the output capacitor. This pin should be placed gd1410 of the Schottky Diode to output hd1410 ground path to prevent switching current spikes from inducing voltage noise into TD Bypass Vin to GND with a suitably large capacitorto eliminate noise on the input.

The device includes a voltage reference, oscillation circuit, error amplifier, internal PMOS and etc. The effectiveness of the PC board to dissipate heat also depends on the size, quantity and spacing of other components on the board, as well as whether the surrounding air is still or moving. The data for these curves was taken with the TD SOP8 package operating as a buck-switching regulator tx1410 an ambient temperature of 25oC still air. SW is the switch node that supplies power to the output.

Vendor Web Site 1 Diodes,Inc. Stresses greater than those listed under Maximum Ratings may cause permanent damage to the device. Allows the switching regulator circuit to be shutdown using logic level signals thus dropping the total input supply current to approximately 30uA. Exposure to absolute maximum rating conditions for extended periods may affect reliability.

  ARITHMETICA UNIVERSALIS ENGLISH PDF

These temperature rise numbers are all approximate and there are many factors that can affect these temperatures. Drive EN pin high to turn on the regulator, drive it low to turn it off.

For best results, external components should be located as close to the switcher IC as possible using ground plane construction or single point grounding. EN is a digital input that turns the regulator on or off. Typical Application Circuit 3. Furthermore, some of these components such as the catch diode will add heat to the PC board and the heat can vary as the input td14410 changes.

To minimize coupling to sensitive circuitry, the PC board copper area connected to this pin should be kept a minimum.

A suitable input bypass capacitor must be present at this pin to minimize voltage transients and to supply the switching currents needed by the regulator. The SOP8 package needs a heat sink under most conditions.

5pcs Power PWM Controller TD1410 Sop8

If open core inductors are used, special care must be taken as to the location and positioning of this type of inductor. The size of the heat sink depends on the input voltage, the output voltage, the load current and the ambient temperature. Power Switch Output Pin. Other factors are, trace width, total printed circuit copper area, copper thickness, single or double-sided, multi-layer board and the amount of solder on the board. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operation is not implied.

Parameters Symbol Test Condition Min. An internal compensation block is built in to minimize external component count. Package thermal resistance and junction temperature rise numbers are all approximate, and there are many factors that will affect these numbers.

EN Allows the switching regulator circuit to be shutdown using logic level signals thus dropping the total input supply current to approximately 30uA. Care must be taken in layout. The TD serves as ideal power supply units for portable devices.

  CARLOS CASTANEDA CALATORIE LA IXTLAN PDF

TD operates from a 3. Hd1410 TD junction temperature rises above ambient temperature for a 2A ts1410 and different input and output voltages. Icc vs Temperature Figure 8. Wiring inductance, stray capacitance, as well as the scope probe used to evaluate these transients, all contribute to the amplitude of these spikes. For the inductor, depending on the physical size, type of core material and the DC resistance, it could either act as a heat sink taking heat away from the board, or it could add heat to the board.

The feedback threshold voltage is 1. The voltage spikes are present because of the fast switching action of the output switch, and the parasitic inductance of the output filter capacitor, To minimize these voltage spikes, special low inductance capacitors can be used, and their lead lengths must be kept short. For the best thermal performance, wide copper traces and generous amounts of printed circuit board copper should be used in the board layout.

This is the positive input supply for the IC switching regulator. Physically locate both resistors near the IC, and route the wiring away form the inductor especially an open core type of inductor. It achieves 2A continuous output current over a wide input supply range with excellent load and td141 regulation. Large areas of copper provide the best transfer of heat lower thermal resistance to the surrounding air, and moving air lowers the thermal resistance even further.

5pcs Power PWM Controller TD Sop8 | eBay

Switching Frequency vs Temperature Figure 6. As in any switching regulator, layout is very important. An enable function, an over current protection function and a short circuit protection function are built inside.

Supply Voltage Input Pin. When using the adjustable version, special care must be taken as to the location of the feedback resistors and the associated wiring. Rapidly switching currents associated with wiring inductance can generate voltage transients which can cause problems.